|
|
 |
 DS11
UNDERWATER CHAIN SAW
Stanley's DS11 Diamond Chain Saw brings a new technology to the diving
concrete industry. With chain segments impregnated with diamond and
laser welded to the chain, you can cut concrete (either wire or rebar
reinforced), brick, concrete block, masonry or stone. Because the DS11
is a chain saw, you can cut square corners and avoid over-cuts or expensive
and time consuming corner drilling that required finishing patching
and additional labor. That's especially important in load bearing walls
where many engineers are specifying no over-cuts. Using the plunge cut
ability of the DS11 you can make cut outs in concrete walls and notch
or trim concrete pipe. You now have the ability to cut a full 18" /
46 cm depth in one pass with a saw that's easily handled and operated
by one diver. Because of the light weight, compact size and maneuverability
of the DS11, work in confined spaces is much easier to accomplish. You
can even make a clean cut all the way to the bottom or base level of
a wall. Whether you're involved in construction, remodeling, demolition,
maintenance or rescue, the Stanley DS11 chain saw will help you complete
your job with efficiency and productivity. For FAQ's about the DS11
click here.
A interlocking trigger, hand guards, and low kickback are designed
in for safety. Hydraulic power doesn't require a flywheel to smooth
power pulses so there is not chain coasting when you release the trigger.
Kickback is also reduced without the centrifugal force from the flywheel
used on other models of chain saws.
The DS11 is sold without bars or chains. You order different length
bars and chains as your circumstances dictate. Bars and chains can be
easily changed in the field as necessary. The DS11 is designed to run
off a HTMA type III hydraulic circuit.
The DS11 is designed for heavy duty operations, it can be used by divers
in any position.
| SPECIFICATIONS |
| ITEM |
U.S.A. |
METRIC |
| CUTTING DEPTHS |
15 or 18 in |
38 or 45 cm |
| BAR LENGTHS |
15 or 18 in |
38 or 45 cm |
| LENGTH (with bar &
chain) |
35 or 38 in |
89 or 97 cm |
| WIDTH |
9 in |
23 cm |
| CHAIN TYPE |
3/8 in Pitch |
| INPUT FLOW RANGE |
12 gpm |
45 lpm |
| INPUT PRESSURE |
2000 psi |
140 bar |
| MAXIMUM FEED FORCE |
45 lbs |
200 Nm |
| OPTIMUM FLOW |
12 gpm |
45 lpm |
| PORTING |
8 SAE O-ring |
| CONNECTOR |
3/8 in. Male
Pipe Hose Ends |
| LUBRICATION / COOLING |
Internal
Water Channels in Bar |
|
MODEL NUMBERS
|
| DS115000 |
Underwater Diamond
Chain Saw |
| |
|
DIAMOND
CHAIN APPLICATION CHART
|
CHAIN TYPE
|
PART NUMBER
|
CORRECT USES
|
INCORRECT USES
|
|
Pinnacle
| 15"=56803
18"=58632
| Very hard aggregate concretes (flint, chert, granite,
etc.) Heavy steel reinforcing (5/8" or 16 mm diameter and
larger). Hard natural stone.
| Soft concretes.
Highly abrasive conditions.
|
|
Ultra
| 15"=56801
18"=56802
| Concrete Block. Masonry. "Green" concretes.
Highly abrasive conditions.
| Any type of steel reinforcing. Medium or Very
Hard aggregate concretes.
|
| Please
read Stanley's Hotline regarding the new diamond chains |
| Part
Number |
Bar
Type and Length |
| 30305 |
15"
Chain Bar For use with 56803 or 56801 Chain |
| 30306 |
18"
Chain Bar For use with 58632 or 56802 Chain |
| |
|
ACCESSORIES
|
| Part Number
| Description
|
| HWP10
| Water Pump Attachment
|
| |
|
TEST EQUIPMENT
|
| Part Number
| Description
|
| 3189
| 20 gpm/75 lmp Flowmeter
|
| 4182
| Flow/Pressure Tester
|
Click here to return to the Steffen
Stanley menu.
Click
here to send a request via E-Mail for more information or a price and
deliver quote
Copyright © 2000 Steffen Inc. All rights reserved.
Revised:
|
